WTB Sportbike

[SXE MX6]

Looking for a fuel injected sport bike
Ninja is prefered, but will also consider YZF, CBR, GSXR.

600cc-1200cc

Have $3500 to spend and would like something that would pass saftey
(needs to be in good mechanical condition)

Don't care if there are some scratch's or small defects in the plastic, etc.

Thanks

[SXE MX6]

up up up and away......

[fredybender]

I know its just a bit higher than budgeted, and its not FI, but a hell of a deal IMHO
Bike is in PERFECT running condition!
$12K just in parts alone invested in the bike, and its NICE!!!
I am not even asking half of the price of the parts !!!
asking price is $5K.

Too many parts to list but even has the rubber spikes on the new dual compund tires...
Bike has always been stored in my living room...
I am a self admitted OCD on bikes & cars...

http://www.gtamotorcycle.com/vbforum...a-lot-invested!

Can deliver too!
Fred

[fredybender]

A small list on what has been done to the bike...


Engine Specifications:

* Stock 750 displacement ; porting job 4 angle valve seat & valve encapsulation.
* New 2 nd & 6th driven gear (undercut too)
* New crank & conrod bearings
* Hone & cross hatch
* new rings, & valves: Lapped
* All new seals, & new wires
* Titanium retainers

Engine Misc.:

* BMC ROSSO filters
* Porting job
* DYNA 2000 ignition
* Dynatek 2.2 ohm coils
* Dynatek ignition wires


Fuel & Tuning:

* Mikunis 38 mm
* Factory Pro stage 3 kit
* 150 mains, 3rd clip from top
* US spec emulsion tubes
* #35 pilot jets

Exhaust:

* Yoshimura R&D slip on

Drivetrain:

* 530 RK Gold X-ring
* -1 in front
* +1 in back
* Factory pro Shift kit
* All new bearings: Wheel , Suspension, swing arm, steering head, etc...

Weight reduction & transfer:
Suspension, wheels & tires:

* Galfer front wave rotors & HH pads
* Lightweight rear rotor
* 05 1000 rear shock
* Tobi side-mount adjustable 19 position steering damper
* Upgraded front forks to full Ohlins internals: .90kg/mm springs, Ohlins cylinders, valves & customed shimed for 170lbs rider
* Michelin Pilot Power 2CT's 190 rear & 120 front
* Flat black powder coated front & rear wheels
* Stainless steel braided brake lines front & back
* Steering head bearing seats beefed up (added aluminum by welding) & line bored machined

Electrical:

* Wiring harness taken appart, re-welded all splices done to it over the years, and shrunk wrap it back. Then all protected by wire wrap

Exterior:

* Clear alternative integrated rear light
* Custom color black metallic fairing
* Custom made undertail clean up out of 6061-T6 Aluminum 0.125 plate, satin black powdercoated
* Front flashers LED 40K Mcd
* NO block off plates!
* Polished frame
* Polished swingarm
* Satin black powder coated rear peg set, upper & lower triples, clip-ons, brackets, & front pegs...etc...
* Satin black powder coated sub-frame
* Black powder coated levers
* Smoke windshield

[rustysteel]

http://www.casc.on.ca/forums/showthr...light=cbr600rr

send me a message with any questions? Price is best offer.

[SXE MX6]

Originally Posted by rustysteel

http://www.casc.on.ca/forums/showthr...light=cbr600rr

send me a message with any questions? Price is best offer.

$3500?



That is what I was looking to spend!